Order n°92cf027610 rond pour cocarde lsf. contour 2mmai.ai

BILLING: SP

EDIT REQUIRED

Failed to preview file please download source

Warning ! Always download the source file, the colors and elements may differ from the preview. (Preview images can have problem please always check source file) Download Original file

Order type : EMBROIDERY
Internal Ref:	Contour new cocarde LSF
Dimensions:	Height: 20mm, Width: 20mm.
Numbers of colors:	1
Fabrics:	coton elasthanne 160gr
Software:	Wilcom Tajima (.dst)
Colorway to use:	Madeira PolyNeon 40
To delivers:	(EMB if Wilcom, or PXF if Pulse, NGS if Wings), .dst, .pes and pdf in french
Comment: Click here to translate	Can you make it like this please : - the needle must start at the top of the cercle, the first running stitche cercle must be 2.1cm width - then cut the thread and make the needle go down 4cm before going up again to its original place - make another runing stitches cercle in 1.9cm width - make the last cercle less puffy please i'll send you a video in a next mail so you can understand better
Notes:

Last edit asked

10-12-2020 16:00
can you put the 1st cerlce at 20mm and the cercle in satin stitches at 21mm. and can you make it for a TAJIMA TMEF-HC912 please? the embroidery doesn't act the same on this machine please

All edit asked

03-11-2020 17:46
can you make it in appliqué please

05-11-2020 16:20
the first cercle must start at the top. then put a stop and cut the thread. can you aslo put the first cercle and last cerlce in 21mm please

06-11-2020 15:18
urgent, every cercle must start from the top of the cerle, and add a cut thread after the first cercle please

13-11-2020 09:30
urgent, the needle needs to start at the top and middle of the cercle, after the first cercle the needle needs to cut the threads and stop, then start again, and can you put the satin cercle a bit less thick please

16-11-2020 10:51
Can you make it like this please : - the needle must start at the top of the cercle, the first running stitche cercle must be 2.1cm width - then cut the thread and make the needle go down 4cm before going up again to its original place - make another runing stitches cercle (no zigzag) in 1.9cm width - make the last cercle less puffy please

19-11-2020 12:01
here is a video so you can understand better we still need the needle to start at the top of the cercle and after the first cercle to cut the thread and make the needle go down 4cm before going up again to its original place please

19-11-2020 12:02
here is the video for more informations

26-11-2020 14:02
see attached file for improvements please

01-12-2020 11:30
can you improve a few things please: the needle is moving before it start threading it should start in place please the first cercle must do 2.1cmn the 2nd one 1.9cm and the last one 2.1cm please we can stil lsee a little dot at the top of the cercle where it first start threading and when the program is done it's going back up to it's original place, the client can't make another one immediatly after can you improve on those points please

07-12-2020 14:36
in the attached file is an older version. we need it like this one but with the correct sizes please

07-12-2020 16:47
see attached file, on the client file we can see that the cross for the needle is at the top of the cercle, on your file though we can see that the cross is way up and the needle starts there before coming down to start the embroidery please

Already uploaded files:

Add new files:

Created by:

Verify files results